How can I make my own colloidal silver?
I'll answer
Earn 20 gold coins for an accepted answer.20
Earn 20 gold coins for an accepted answer.
40more
40more
Lucas Ross
Works at the International Development Association, Lives in Washington, D.C., USA.
As a chemist with experience in colloidal solutions, I can guide you through the process of making colloidal silver. However, it's important to note that colloidal silver is not approved by the FDA for any medical use and can be harmful if not prepared properly. With that said, here's a basic method for creating colloidal silver:
Materials:
- Distilled water
- Silver wire or silver nitrate
- A glass container
- A 12-volt battery-powered electrolytic cell (optional)
- A 9-volt battery (for the electric current method)
- A small piece of copper wire (for the electric current method)
Procedure:
1. Clean the glass container and all equipment with distilled water to avoid contamination.
2. Fill the container with distilled water. If using silver wire, you can place it directly in the water. If using silver nitrate, dissolve a small amount in the water.
3. If using the electrolytic method, connect the silver to the positive terminal and the copper to the negative terminal of the battery-powered cell. Place both in the water.
4. If using the electric current method, connect the silver and copper wires to the positive and negative terminals of the 9-volt battery, respectively. Then, dip both wires into the water.
5. Turn on the power source and allow the current to pass through the water for several hours. This will cause the silver ions to be reduced and form silver nanoparticles.
6. Monitor the color of the solution. As colloidal silver forms, it will take on a yellow or golden hue.
7. Once the desired color is reached, turn off the power source and remove the silver and copper from the water.
8. Let the solution sit undisturbed for a few hours to allow larger particles to settle at the bottom.
9. Carefully decant the clear colloidal silver from the top, leaving the sediment behind.
Safety Precautions:
- Always wear protective gear such as gloves and safety glasses.
- Work in a well-ventilated area.
- Do not ingest colloidal silver as it can cause argyria, a condition that turns the skin blue-gray.
**Please remember that this is a simplified explanation and actual laboratory procedures may vary.**
Materials:
- Distilled water
- Silver wire or silver nitrate
- A glass container
- A 12-volt battery-powered electrolytic cell (optional)
- A 9-volt battery (for the electric current method)
- A small piece of copper wire (for the electric current method)
Procedure:
1. Clean the glass container and all equipment with distilled water to avoid contamination.
2. Fill the container with distilled water. If using silver wire, you can place it directly in the water. If using silver nitrate, dissolve a small amount in the water.
3. If using the electrolytic method, connect the silver to the positive terminal and the copper to the negative terminal of the battery-powered cell. Place both in the water.
4. If using the electric current method, connect the silver and copper wires to the positive and negative terminals of the 9-volt battery, respectively. Then, dip both wires into the water.
5. Turn on the power source and allow the current to pass through the water for several hours. This will cause the silver ions to be reduced and form silver nanoparticles.
6. Monitor the color of the solution. As colloidal silver forms, it will take on a yellow or golden hue.
7. Once the desired color is reached, turn off the power source and remove the silver and copper from the water.
8. Let the solution sit undisturbed for a few hours to allow larger particles to settle at the bottom.
9. Carefully decant the clear colloidal silver from the top, leaving the sediment behind.
Safety Precautions:
- Always wear protective gear such as gloves and safety glasses.
- Work in a well-ventilated area.
- Do not ingest colloidal silver as it can cause argyria, a condition that turns the skin blue-gray.
**Please remember that this is a simplified explanation and actual laboratory procedures may vary.**
reply(1)
Helpful(1122)
Helpful
Helpful(2)
Studied at the University of British Columbia, Lives in Vancouver, Canada.
EVERY 4 or 5 minutes you need to:Turn off the power,Remove the silver wires from the jar,Wipe the two silver wires with a paper towel AND a non-metallic pot scrubbing pad (e.g. 1/4�� thick nylon Scotchbright pad),Put the silver wires back into the water, and.Turn the power back on.
2023-04-07 14:05:06
Ethan Brown
QuesHub.com delivers expert answers and knowledge to you.
EVERY 4 or 5 minutes you need to:Turn off the power,Remove the silver wires from the jar,Wipe the two silver wires with a paper towel AND a non-metallic pot scrubbing pad (e.g. 1/4�� thick nylon Scotchbright pad),Put the silver wires back into the water, and.Turn the power back on.
